For use with Innovative Mounts Conversion Kit Part # 49150
Please Read Before Starting: This kit is designed to bolt in B-series engines into a 88-91 Civic or CRX. Make sure your
B-series engine has the left-hand engine bracket from the 90-93 Acura Integra or first generation B-16A.
If you need one it can be ordered from us directly or Acura (part # 11910-PR3-010).
Before you begin, make sure you have the proper rear engine/transmission bracket for your engine’s
installation. If your B16A, B17A and B18A engine did not come with a rear bracket, or you have a B18C,
B18B and B20B/Z engine, you will need to purchase one from Acura part no. 50827-SK7-020. It is the rear
engine bracket for a 90-93 Acura Integra. NOTE: The two holes on the rear bracket for the two lower bolts
at the transmission will need to be enlarged to accept the 14mm x 1.25 bolts that go with that
Engine bay preparation:
1. Test fit the rear mount on the rear engine cross-member. The area of the rear cross-member may need to
be bent down to clear the rear engine bracket (T Bracket). Test fit the bracket on the mount after bending
the cross-member to make sure enough was bent down.
2. A dent must be made directly below the opening on the driver's shock tower for alternator clearance.
The dent needs to be approximately 3/8” to 1/2" deep. Make sure you double-check the alternator clearance
after bolting the engine in the car. Also depending on the engine you are using, sometimes you can also
gain added clearance by using a smaller belt.
3. You will need to either use an aftermarket front crossmember or modify your existing one by cutting off the
original engine mount bracket for the front mount. Also if you are using an aftermarket header you may need to
modify your existing crossmember for clearance.
Hydraulic conversion installation:
Note: We recomend doing these steps before installing engine into the engine bay.
1. Bolt the release arm lever and bracket to the front of the transmission using the top two of three 12mm
boltholes on the front of the transmission.
2. Install the cable bracket using two 8mm x 1.25mm x 25mm bolts. Torque the bolts to 19 ft/lbs.
Mount kit and engine installation:
Note: We recomend removing the radiator from the car before installing the new engine so that it will not
be damaged. It will also allow for more space to maneuver the engine into place.
1. The rear mount should be bolted into position after the rear cross-member has been altered for
clearance. Do not attach the rear bracket to the rear mount at this time. The rear bracket should be
installed later, as the engine is lowered or raised into position. It is best to have help when doing this
if you are installing the engine in from the top. You will need a box end wrench to tighten the rear bolt.
2. If you are installing the engine from the bottom, you can go ahead and install the right-hand mount on
the transmission. If you are installing the engine from the top, you will need to drop the engine down
below mounting position and then install the mount. Then raise the engine back into place while installing
the rear bracket. Do not completely tighten the bolts on the rear bracket yet. Notice the right-hand mount
has slotted holes where the mount bolts to the top of the mount does not line up perfectly the frame rail
bracket you can use slotted holes to shift the mount to the right or left to compensate. This may or may
not be necessary with your car. It depends on your vehicles past history and manufacturers tolerances.
3. Next install the left-hand engine mount, but do not completely tighten the bolts. Use a 12mm x 50mm
bolt and lock nut on the front bolthole and another lock nut on the stud. Make sure you also use 12mm
washers under the lock nuts.
4. Install the top bolts on the rear engine bracket where it meets the engine and the rear mount. Now go
back and tighten the mount bolts on the right and left mounts. Finally install the two bolts on the bottom
of the rear bracket where it meets the transmission and tighten all the bracket bolts. After 100-200 miles
of driving, check and re-torque all the mount bolts to factory specifications.
Note: We always recomend leaving all bolts finger tight until your engine is properly placed, with the
engine properly secured.
Clutch Cable Installation:
1. Make sure the clutch cable adjustment nut is adjusted all the way to the top first, and then slide the
clutch cable through the holder. Now raise the release lever up and slide the clutch cable into the
slotted end. Seat the clutch cable stop into the opening of the lever.
2. Slide the release rod over the end of the release arm on the transmission as shown and tighten the
bolt until the wave-lock washer flattens completely.
3. Bolt the rod end of the release rod to the release lever and torque to 19 ft/lbs.
4. Adjust the clutch cable adjusting nut as you would normally would for your car. After test-driving the
car, some additional adjusting may need to be done to get the clutch’s release point in the ideal